|
LMA Papers
LMA Website
Policies
Search LMA
Submit a Paper
Notify me of new papers
|
 |
Consortium on Deburring and Edge Finishing
CODEF was established to address problems related to prediction and modeling of burr and edge breakout phenomena, development of a data base (or knowledge base) of best burr avoidance and removal techniques from industry, development of a computer aided design (CAD) advisor (a burr expert) for designers and process planners, development of strategies for deburring cell level process feedback and control and identification and development of advanced deburring technologies. Although all manufacturing processes are of interest in this program, of special interest is those processes for precision manufacturing. The program also provides a forum for the discussion of standards and terminology associated with the field.
|
PAPERS FROM 2007
|
| Sangkee Min, David Dornfeld, J. Kim, and B. Shyu (June 27, 2007) Finite Element Modeling of Burr Formation in Metal Cutting |
| Paul K. Wright, David Dornfeld, V. Sundararajan, and Debananda Misra (May 2, 2007) Tool Path Planning Generation For Finish Machining of Freeform Surfaces in the Cybercut Process Planning Pipeline |
|
PAPERS FROM 2006
|
| Miguel C. Avila, Joel D. Gardner, Corinne Reich-Weiser, Athulan Vijayaraghavan, and David Dornfeld (July 1, 2006) Strategies for Burr Minimization and Cleanability in Aerospace and Automotive Manufacturing |
| Corinne Reich-Weiser and David Dornfeld (July 1, 2006) Experimental Investigation of the Influence of Machining Parameters on Chip Geometry for Enhanced Cleanability |
| Athulan Vijayaraghavan and David Dornfeld (July 1, 2006) Automated Drill Modeling for Drilling Process Simulation |
| Athulan Vijayaraghavan, David Dornfeld, and C. K. Hari Dharan (July 1, 2006) Quantifying Edge Defects in Drilled FRP Composites |
| Miguel C. Avila, Corinne Reich-Weiser, David Dornfeld, and Sara McMains (June 1, 2006) Design and Manufacturing for Cleanability in High Performance Cutting |
| Joel D. Gardner and David Dornfeld (June 1, 2006) Finite Element Modeling of Drilling Using DEFORM |
| Jeffrey Hartnett, Sangkee Min, and David Dornfeld (June 1, 2006) Fabrication of Protruding Features in a Micro-Mold: a Planning Report |
| Corinne Reich-Weiser (May 1, 2006) An Experimental Investigation on the Influence of Process Parameters During Chip Formation |
| Shantanu Tripathi and David Dornfeld (January 1, 2006) Review of Geometric Solutions for Milling Burr Prediction and Minimization |
| Paul K. Wright, David Dornfeld, R. G. Hillaire, and Nathan K. Ota (January 1, 2006) A Wireless Sensor for Tool Temperature Measurement and its Integration within a Manufacturing System |
|
PAPERS FROM 2005
|
| Miguel C. Avila and David A. Dornfeld (July 1, 2005) Exit Order Sequence Burr Prediction Algorithm Based on Rectangular Coordinates |
| Joel D. Gardner, Athulan Vijayaraghavan, and David A. Dornfeld (July 1, 2005) Comparative Study of Finite Element Simulation Software |
| Corinne Reich-Weiser and David A. Dornfeld (July 1, 2005) Drilling Burr Control Chart -Adding a Material Property Axis |
| Shantanu Tripathi and David A. Dornfeld (July 1, 2005) Tool Path Planning for Reconfigurable Machines |
| Athulan Vijayaraghavan and David A. Dornfeld (July 1, 2005) Challenges in Modeling Machining of Multilayer Materials |
| M. Eugene Merchant, David Dornfeld, and Paul K. Wright (May 1, 2005) Manufacturing — Its Evolution and Future |
| Kiha Lee and David Dornfeld (April 1, 2005) Micro-Burr Formation and Minimization Through Process Control |
|
PAPERS FROM 2004
|
| David Dornfeld (October 1, 2004) Strategies for Preventing and Minimizing Burr Formation |
| Miguel C. Avila and David A. Dornfeld (May 31, 2004) On The Face Milling Burr Formation Mechanisms and Minimization Strategies at High Tool Engagement |
| Miguel C. Avila, Jihong Choi, David A. Dornfeld, Michael Kapgan, and Rick Kosarchuk (May 31, 2004) Deburring of Cross-Drilled Hole Intersections by Mechanized Cutting |
| H Z. Choi, S W. Lee, G H. Kim, Y J. Choi, and Sung-Lim Ko (May 31, 2004) Micro Deburring Technology Using Ultrasonic Vibration with Abrasive |
| Jihong Choi, Sangkee Min, and David A. Dornfeld (May 31, 2004) Finite Element Modeling of Burr Formation in Drilling of a Multi-Layered Material |
| Kiha Lee and David A. Dornfeld (May 31, 2004) A Study of Surface Roughness in the Micro-End-Milling Process |
| Sangkee Min, Dae-Eun Lee, Arnaud de Grave, Carlos M. De Oliveira Valente, Judy Lin, and David A. Dornfeld (May 31, 2004) Surface and Edge Quality Variation in Precision Machining of Single Crystal and Polycrystalline Materials |
| Arvind Rangarajan and David A. Dornfeld (May 31, 2004) Back Cutting and Tool Wear Influence on Burrs in Face Milling - Analysis and Solutions |
| Wendy Shefelbine and David Dornfeld (May 31, 2004) Influences on Burr Size During Face-Milling of Aluminum Alloys and Cast Iron |
| Wendy Shefelbine and David A. Dornfeld (May 31, 2004) The Effect of Dry Machining on Burr Size |
| Arvind Rangarajan and David Dornfeld (January 1, 2004) Efficient Tool Paths and Part Orientation for Face Milling |
|
PAPERS FROM 2003
|
| Miguel C. Avila and David A. Dornfeld (June 1, 2003) The Effect of Kinematical Parameters and Tool Geometry on Burr Height in Face Milling of Al-Si Alloys |
| Alexander Balduhn and David A. Dornfeld (June 1, 2003) Model of a Burr Expert System |
| Jihong Choi, Sangkee Min, and David A. Dornfeld (June 1, 2003) Modeling of Inter-Layer Gap Formation in Drilling of a Multi-Layered Material |
| Kiha Lee and David A. Dornfeld (June 1, 2003) Micro-Burr Formation and Minimization through Process Control |
| Prabhu Ramachandran and David A. Dornfeld (June 1, 2003) Feasible Offset Region Based Tool Path Planning for Face Milling |
| Arvind Rangarajan and David A. Dornfeld (June 1, 2003) Determining Statistically Significant Parameter Regions for Bounded Specification |
| Arvind Rangarajan and David A. Dornfeld (June 1, 2003) Probabilistic Precision Process Planning- P4 |
| Arvind Rangarajan and David A. Dornfeld (June 1, 2003) White Paper on Technical Software Integration |
| G. Byrne, David Dornfeld, and B. Denkena (January 1, 2003) Advancing Cutting Technology |
| Jihong Choi, Sangkee Min, David Dornfeld, Mahboob Alam, and T. Tzong (January 1, 2003) Modeling of Inter-Layer Gap Formation in Drilling of a Multi-Layered Material |
| Sangkee Min, David Dornfeld, and Yohichi Nakao (January 1, 2003) Influence of Exit Surface Angle on Drilling Burr Formation |
|
PAPERS FROM 2002
|
| Jinsoo Kim and David Dornfeld (January 1, 2002) Development of an Analytical Model for Drilling Burr Formation in Ductile Materials |
|
•
•
•
•
